Brother Unable To Init 50

Posted on by
  1. Unable To Init Dxgi
  2. Unable To Init 50 Brother Dcp-j315w
Brother

If the LCD displays 'Machine Error 46', the ink absorber pad is full and needs replacing. please refer to 'How do I clear Machine Error 46?'

The message 'Unable to -' ( 'Unable to Change' 'Unable to Clean' 'Unable to Init' 'Unable to Print' 'Unable to Scan' ) is a general message and may appear for different reasons.

Thank you so much for posting this. My Brother MFC 440CN — which has been a wonderful and reliable printer — wouldn’t print and gave me the Unable To Print 51 code. Accent rar password recovery serial. It turned out that my gear was cracked, just like yours. I was able to open up the crack with a jewelers screwdriver and drizzle super glue into the crack and onto the shaft. If one of the following messages is displayed on the LCD, the machine may have a mechanical problem, a dirty encoder strip or a foreign object such as a clip or ripped paper inside the machine.

To clear the message, you need to disconnect the Brother machine from the power outlet to check the machine.

Follow the steps listed below:

  1. Check for foreign objects, such as a paper clip or scrap of paper, inside the machine.
    Disconnect the machine from the power outlet and open the scanner cover by pulling up on the lower right corner of the cover. Look inside the machine and remove any foreign objects. If you see jammed paper or another item inside this area, gently pull it out and then close the scanner cover securely.
  2. If the error continues to appear, move the print head and examine under the print head.

NOTE: The images shown below are from the representative product and may differ from your Brother machine, but their inner structures are same.

2-1.Disconnect the Brother machine from the poweroutlet.
2-2.Open the scanner cover.

2-3.Check the print head's position.
In the example photo the print head is positioned at the left hand side of the platen area.


  • If the print head is on the left side, go to step 2-4.
  • If the print head is on the right side, go to step 2-7.
  • If you can not find the print head, go to step 2-8.

2-4.Gently move the print head to the center.


2-5.Examine under the print head. If anything is found, remove it.



Use a flashlight if necessary to check thoroughly.

2-6.Close the cover and reconnect the machine to the power outlet.


If the message continues to appear on the LCD, the machine will require repair.


2-7. If the print head is on the right side.


The print head is positioned at the far right hand side, you cannot move it.

The machine has a mechanical malfunction and will require repair.


2-8. If you can not find the print head.


The machine has a mechanical malfunction and will require repair.


One day I've encountered about this error 'Clean unable 50' displaying at my Brother DCP 195C screen. Immediately I search online for the needed solutions. And luckily I've found one.
The following are the procedure on how to fix the 'Clean unable 50' error of the Brother DCP 195C printer.
1. Plug in the printer and turn it ON.
2. Usually the error display's on screen, Press OK.
3. Then press MENU.
Unable to init 50 brother mfc j5910dw4. Press MONO.
5. Press the UP ARROW four(4) times. Then you notice that the ATTENTION LED and the PHOTO CAPTURE button are simultaneously blinking.
6. Enter 80 to go to maintenance mode. When encoding the numbers (80) follow this:
Brother - press UP ARROW button until the number 8 appears. press OK.
- press UP ARROW button until the number 0 appears. press OK.

Unable To Init Dxgi

7. Next, press continuously the MONO button until the 'Purge:________' appeared.
Brother8. Now, enter 2783 by doing the same procedure on step 6. The counter will be reset.
9. Press STOP/EXIT.

Unable To Init 50 Brother Dcp-j315w

10. Enter 99 by doing the same procedure on step 6 to exit Maintenance Mode.
The printer will automatically restart and works normally.